每次制造完畢后，用抺布將HDPE儲罐表面清洗整潔，嚴禁用很多的水持續清洗機器設備外界，防止隔熱層毀壞。

按加工工藝規定，制造一定時間后，解決罐里開展清理。長時間，超出72鐘頭，停工后，開課前機器設備應再次清理。

清理規范，單種類應用的機器設備清理至不可以發覺可視性臟物；好幾個種類應用的同一臺機器設備在拆換種類時按加工工藝規定實行。

清理實際操作人應立即填好清理紀錄，工作經驗收入工程驗收并簽名確定。

進到HDPE儲罐中清理該罐時應按標準規定的要求開展。進到機器設備內清理時，應在釜底鋪平海綿墊，以防專用工具掉入，并須穿膠底鞋，以防損害夾層玻璃面。

儲罐的筒夾內禁止進到酸液。如果清理筒夾一定得用酸液時，不可以用pH＜2的酸液，酸液進到該機器設備夾套會造成氫效用，造成表層像魚鱗片大規模掉下來，一般清理筒夾能用百分之二的次氯酸鈉溶液，再自來水清理筒夾。

After each manufacturing, clean the surface of HDPE storage tank with cloth. It is strictly prohibited to continuously clean the outside of machinery and equipment with a lot of water to prevent the damage of thermal insulation layer.

According to the processing technology, clean the tank after manufacturing for a certain time. For a long time, more than 72 hours, after shutdown, the machinery and equipment shall be cleaned again before class.

Cleaning specification: separate types of machines and equipment shall be cleaned so that no visible dirt can be found; For the same machine and equipment used in several types, it shall be replaced according to the processing technology regulations.

The actual cleaning operator shall immediately fill in the cleaning records, and the work experience shall be included in the project acceptance and signed for confirmation.

When entering into HDPE storage tank and cleaning the tank, it shall be carried out according to the requirements specified in national standards. When entering the machinery and equipment for cleaning, the sponge pad shall be paved at the bottom of the Buss to prevent special tools from falling in, and rubber soled shoes shall be worn to prevent damage to the laminated glass surface.

No acid is allowed into the collet of the storage tank. If the acid solution must be used to clean the collet, the acid solution with pH < 2 can not be used. The acid solution entering the jacket of the machine and equipment will cause hydrogen effect and cause the surface to fall off like fish scales on a large scale. Generally, the collet can be cleaned with 2% sodium hypochlorite solution and tap water.